Model Ship Builder :: Forums :: Build Logs :: POF Build Logs |
|
<< Previous thread | Next thread >> |
Model Shipways Typical Ship’s Boat |
Go to page 1 2 3 4 5 6 7 8 9 | |
Moderators: Winston, aew
|
Author | Post | ||
Jonathan G |
| ||
![]() ![]() Registered Member #4155 Joined: Thu Mar 14 2013, 09:01pmPosts: 1159 | These were glued in place, trimmed and sanded.![]() ![]() | ||
Back to top | | ||
Jonathan G |
| ||
![]() ![]() Registered Member #4155 Joined: Thu Mar 14 2013, 09:01pmPosts: 1159 | The bow was covered with teak plank. ![]() | ||
Back to top | | ||
Jonathan G |
| ||
![]() ![]() Registered Member #4155 Joined: Thu Mar 14 2013, 09:01pmPosts: 1159 | The oarlocks were made of bamboo pieces just like one would make treenails, about a quarter the width of the soon to be made oars (about 1/32”) and placed into a pre-drilled kit supplied basswood planking strip. Initially the holes were drilled and the oarlock inserted. Their heights were adjusted and then the whole assembly was stained with Early American. The stain temporarily “glued” the bamboo into position. After the stain dried, the excess was cut off from the bottom and sanded smooth. The oarlock assemblies were then cut off and glued into position onto the rail cap locking everything – the rail cap, oarlock plate, and the bamboo with a single dab of CA glue.![]() ![]() | ||
Back to top | | ||
Gary M |
| ||
![]() Registered Member #4198 Joined: Tue May 07 2013, 10:50pmPosts: 904 | Jonathan, A job well done. I love the scarph joints on the gunwales as well as the oar locks. Gary | ||
Back to top | | ||
Tim C |
| ||
![]() ![]() Registered Member #4126 Joined: Fri Feb 15 2013, 05:19amPosts: 1113 | Nice Job. Later Tim | ||
Back to top | | ||
aew |
| ||
aew![]() ![]() ![]() Registered Member #1929 Joined: Wed Nov 30 2011, 03:05pmPosts: 3010 | Very nicely done Jonathan. However I hate to ask awkward questions, but haven't you got the positioning of them reversed? Sitting on a seat and facing a rowlock would mean that you were facing forward and rowing astern. | ||
Back to top | | ||
Tim C |
| ||
![]() ![]() Registered Member #4126 Joined: Fri Feb 15 2013, 05:19amPosts: 1113 | So true. I missed that one also. I liked the idea on how it was done. Later Tim | ||
Back to top | | ||
Jonathan G |
| ||
![]() ![]() Registered Member #4155 Joined: Thu Mar 14 2013, 09:01pmPosts: 1159 | A strip of wood, which I think is called a washboard, was added to each side of bow as well another eyebolt and ring to the bow deck. Also notice that the oarlocks were moved after I was informed by (aew & Tim C) that I had inadvertently installed them on the wrong side of the thwarts. As originally installed, the rowers would have to face forward and row the boat backwards. Thanks guys for pointing that embarrassing error out. ![]() | ||
Back to top | | ||
Jonathan G |
| ||
![]() ![]() Registered Member #4155 Joined: Thu Mar 14 2013, 09:01pmPosts: 1159 | The Rudder The kit provided a precut basswood rudder which I used. However, you remember I broke the top of rudder stem where it protruded above the transom. The two images below show the before and after the break ![]() ![]() | ||
Back to top | | ||
Jonathan G |
| ||
![]() ![]() Registered Member #4155 Joined: Thu Mar 14 2013, 09:01pmPosts: 1159 | After looking at a lot of small and ship’s boats, I came to the conclusion that most of the boats I saw did not have the high stem post, so I chose to leave it off. Had I straight glued the broke piece back on, it would have remained fragile which would mean I would have had to pin it and risk breaking it some more. All that being said, the rudder was now too tall for what I wanted to do, so the tiller post was cut down a bit. ![]() | ||
Back to top | | ||
Go to page 1 2 3 4 5 6 7 8 9 | |
Powered by e107 Forum System