Forums / POF Build Logs / H.M.S. Triton 1:48 scale cross section

Forums

Model Ship Builder :: Forums :: Build Logs :: POF Build Logs		<< Previous thread \| Next thread >>
H.M.S. Triton 1:48 scale cross section

Go to page 1 2 3 4 ... 13 14 15
Moderators: Winston, aew, bikepunk

Author

Post

Gary M

Fri Feb 14 2014, 01:33pm

Registered Member #4198

Joined: Tue May 07 2013, 10:50pm
Posts: 908

Raymond, I too, enjoy your logs and your fine work. Keep up the great work and and keep sharing it with us. One of the things I like about these forums is the fact that there are so many ways to approach a problem or build a model. I learn from all of them. Looking forward to this weeks progress! Gary

Mike 41

Fri Feb 14 2014, 01:46pm

Registered Member #702

Joined: Fri Feb 05 2010, 10:37pm
Posts: 1238

Hi Ray,

Your frames look great! Like Gene says it doesn’t matter which method you use as long as you have fun and like the finished model. I have used both methods and they work equally well I like to add trenails on each side of the joints. I like to use 20 gauge brass or copper wire because it is faster that making bamboo ones.

You are off to a good start just stay with it.

Mike

Tim C

Fri Feb 14 2014, 01:47pm

Registered Member #4126

Joined: Fri Feb 15 2013, 05:19am
Posts: 1105

Your doing Great. Keep on singing "I did it my way". Your frame raising is going great.
It's easy to poke fun and other such stuff. I hope that mods step in and remove said posts.
Good Luck and enjoy doing it your way.

Later Tim

aew

Fri Feb 14 2014, 02:34pm

aew

Registered Member #1929

Joined: Wed Nov 30 2011, 03:05pm
Posts: 2751

Raymond: I had a look at the posts on MSW and I'm pretty sure I know which one you'r referring to. The closing comment is uncalled for.

I've seen quite a few comments from people saying they don't like the site because of such posts. There are plenty of helpful people over there, it's the odd one or two that create that impession.

I certainly wouldn't let it put me off, I also would continue to do it myway and I'd cross him off my Christmas list.

Constructive criticism is a different matter, I'll take all of that I can get.

You could PM him this link to the Elvis version: http://www.youtube.com/watch?v=z2aKc_AdOVE $\:D/$

Winston

Fri Feb 14 2014, 03:07pm

winston

Registered Member #1

Joined: Sat Jun 13 2009, 02:08pm
Posts: 2293

Different strokes for different folks I always say. Look, listen and read everything thing you can and then do what works for you. Ultimately you are the one that has to be happy with the results.

Don't take to heart anyone's comments online. Words mean different things to different people. More often than not they are meant to be helpful. Just try to read between the lines, get the message they are trying to get across to you and if it's useful to you make use of it. If not, move on.

Raymond Deliz

Fri Feb 14 2014, 09:42pm

Registered Member #4329

Joined: Thu Dec 12 2013, 06:21pm
Posts: 382

Gentlemen,
I greatly appreciate all your words of confidence and advice to this matter. I truly believe that if people take their time to vent before engaging in written communication they will be able to express themselves in such a way as to avoid misunderstandings.

Winston

Fri Feb 14 2014, 11:45pm

winston

Registered Member #1

Joined: Sat Jun 13 2009, 02:08pm
Posts: 2293

Isn't that the truth!!!

Raymond Deliz

Sat Feb 15 2014, 03:32am

Registered Member #4329

Joined: Thu Dec 12 2013, 06:21pm
Posts: 382

Greetings to all,
Since I had to work today I was not able to get much done on the Triton. I was able to buy more timber and finish my jig for her reusing materials for the jig I made for my Vietnamese Junk. Since she is only a cross section, the jig seems small in comparison to jigs other people use while conducting full builds. The following photos will show you what it looks like and how the Triton fits within it.