Model Ship Builder :: Forums :: Build Logs :: POF Build Logs |
|
<< Previous thread | Next thread >> |
USS Peacock POF 1:48 - Scratch |
Go to page 1 2 3 ... 9 10 11 12 | |
Moderators: Winston, aew
|
Author | Post | ||
Bill Edgin |
| ||
![]() ![]() Registered Member #4362 Joined: Wed Jan 22 2014, 02:37amPosts: 373 | Great job Gary! | ||
Back to top | | ||
Gene Bodnar |
| ||
![]() ![]() Registered Member #126 Joined: Tue Jul 21 2009, 11:20amPosts: 1778 | Gary, Very well done. Gene | ||
Back to top | | ||
Gary M |
| ||
![]() Registered Member #4198 Joined: Tue May 07 2013, 10:50pmPosts: 904 | Thanks for the kudos, Gene and Mike. Framing Jig and Framing Plan: The Framing Jig is set at WL 5. My rationale is that it is at the free board where there is not a significant amount of bevel to contend with. You will note the extended slot for the cut water at the bow. Also marked is the termination of the keel at the stern where a block should be placed. The Framing Plan is a simple drawing that was fun to do. It shows the hawse timbers. I still need to mark the transom timbers and side filler pieces. If you open the PDF, the resolution will be much higher. ![]() ![]() | ||
Back to top | | ||
Mike 41 |
| ||
![]() ![]() Registered Member #702 Joined: Fri Feb 05 2010, 10:37pmPosts: 1245 | Hi Gary, Your framing jig look great! You may want to consider cutting the notches for the frames a little deeper on the next one. Mike | ||
Back to top | | ||
Gary M |
| ||
![]() Registered Member #4198 Joined: Tue May 07 2013, 10:50pmPosts: 904 | Hi Mike, No problem. I will do that over the weekend. I assume you are talking about the tabs in the jig? Thanks! G | ||
Back to top | | ||
Mike 41 |
| ||
![]() ![]() Registered Member #702 Joined: Fri Feb 05 2010, 10:37pmPosts: 1245 | Hi Gary, The tabs in the jig look a little short but would work OK. Mike | ||
Back to top | | ||
Gary M |
| ||
![]() Registered Member #4198 Joined: Tue May 07 2013, 10:50pmPosts: 904 | Here are the semi-final draft plans for the Peacock. Still to go are the counter frames, deck plan and a redo of the bow cant frames. I have formatted to fit onto seven sheets at 1:48. ![]() ![]() ![]() | ||
Back to top | | ||
Gary M |
| ||
![]() Registered Member #4198 Joined: Tue May 07 2013, 10:50pmPosts: 904 | Im having touble uploading the pdfs for clearer viewing - its on my end. Will get those up shortly. G [ Edited Tue Oct 21 2014, 03:51pm ] | ||
Back to top | | ||
Gary M |
| ||
![]() Registered Member #4198 Joined: Tue May 07 2013, 10:50pmPosts: 904 | Here are the draft pdf's. Let me know if you see something amiss! G![]() ![]() ![]() | ||
Back to top | | ||
Gary M |
| ||
![]() Registered Member #4198 Joined: Tue May 07 2013, 10:50pmPosts: 904 | And some frames... | ||
Back to top | | ||
Go to page 1 2 3 ... 9 10 11 12 | |
Powered by e107 Forum System