| Model Ship Builder :: Forums :: Current Projects :: Batteau |
|
<< Previous thread | Next thread >> |
| Batteau Prototype 1/24 Scale | ||
| Go to page 1 2 3 4 | |
|
Moderators: Winston, aew, bikepunk
|
| Author | Post | ||
| teleman |
| ||
  Registered Member #1925 Joined: Tue Nov 29 2011, 05:32amPosts: 1254 | Paddy the Bateau is a great little scratch build for a first time. I enjoyed building her. You won't be a rookie for very long, but you will beasking questions until you can't model anymore. Thats the fun part, it never gets old...just you do...LOL! | ||
| Back to top | | ||
| Patrick (Paddy) |
| ||
  Registered Member #4100 Joined: Thu Jan 10 2013, 03:49pmPosts: 208 | Hi Mike, Another question if you don't mind. What thickness are the hull planks (would that be strakes)? If the dimension is on the plan I missed it in my first pass. What I think is an edge view of the planking on a plan view I measured 1/32 of an inch. Is that correct? Thanks. [ Edited Thu Jan 17 2013, 02:20pm ] | ||
| Back to top | | ||
| teleman |
| ||
| Registered Member #1925 Joined: Tue Nov 29 2011, 05:32amPosts: 1254 | Hi Paddy, If your building the Batteau at the same scale it's 1/16" thick basswood I used on my build for the planks..hope this helps... | ||
| Back to top | | ||
| Mike 41 |
| ||
 Registered Member #702 Joined: Fri Feb 05 2010, 10:37pmPosts: 1238 | Hi Paddy, The hull planks are 1/16” thick. I used yellow heart for the hull planking but you can use any wood you like. If I was going to paint the boat I would have used basswood. Have fun! Mike | ||
| Back to top | | ||
| donfarr |
| ||
| Registered Member #2001 Joined: Fri Dec 23 2011, 09:51pmPosts: 1298 | Hi Paddy, It is 1/16 I used boxwood. Don | ||
| Back to top | | ||
| Patrick (Paddy) |
| ||
| Registered Member #4100 Joined: Thu Jan 10 2013, 03:49pmPosts: 208 | Thanks gents. :>). I was starting to think that I may have to make a piano wire jig with the wire mounted parallel on a base and lay some wood between them and sand away. A technique I use to use when I was building Penny Planes to fly indoors. Now to find a supplier if I don't use basswood. Thanks again. | ||
| Back to top | | ||
| teleman |
| ||
| Registered Member #1925 Joined: Tue Nov 29 2011, 05:32amPosts: 1254 | Hey Paddy, You can go to Midwest model on the www or mico mark or ebay for midwest wood products....just a fyi... | ||
| Back to top | | ||
| donfarr |
| ||
| Registered Member #2001 Joined: Fri Dec 23 2011, 09:51pmPosts: 1298 | Hi Paddy, For woods other than Basswood go to Hobby Mill or Lumberyard both are great I use them all the time. Don | ||
| Back to top | | ||
| Patrick (Paddy) |
| ||
| Registered Member #4100 Joined: Thu Jan 10 2013, 03:49pmPosts: 208 | Hi Mike, Did you turn the cannon on your bateau, or is that classed as a caaonade, on your micro lathe? [ Edited Sat Feb 02 2013, 02:00pm ] | ||
| Back to top | | ||
| Mike 41 |
| ||
| Registered Member #702 Joined: Fri Feb 05 2010, 10:37pmPosts: 1238 | Hi Paddy, The cannon is a breach loading swivel gun and I did turn it on my micro lathe. Mike | ||
| Back to top | | ||
| Go to page 1 2 3 4 | |
Powered by e107 Forum System