Forums / POB Build Logs / Calella OcCre kit nb 52002

Forums

Model Ship Builder :: Forums :: Build Logs :: POB Build Logs		<< Previous thread \| Next thread >>
Calella OcCre kit nb 52002


Moderators: Winston, aew

Author

Post

Charles

Tue Aug 21 2018, 02:13am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

Build log of the Calella
OcCre kit Ref : 52002 at 1:15 scale

That project is a bit a funny one, at the end of last October (2008) I was sit at my office desk looking at OcCre catalogue of ship and showing some build in the yard to a colleague I was showing him the Carmella Carmina that Shere build.

At that time he point in the catalogue the Calella and said that he saw that boat somewhere. Ok no comment from me and back to work.

3 days later he came at my desk with a photo of his grand father a fisherman from Spain and guest what here you have an exact Calella. I was surprise even more when my friend ask me how much cost a boat like that and if I will accept to build it for him, as he want to offer it to his dad as a gift for Christmas. I said yes and place an order for 2 as my Lady want one for us. to have the kit ASAP and have plenty time to build it as we where last week of October.

Murphy law
OcCre do not have a master distributor in Canada It is Model Expo that got the licence for north America and guest what my store buy from Model Expo (it was cheaper for me true my store) a case of minimum billing and freight allow. The kits arrive on the 10 of December no time to build it for Christmas.

So I give the empty box to my friend and he wrap it to give to his dad.

Now the kit
Anyone that have build an OcCre kit before already know how well ant the attention given to the packaging. It come as usual with an instruction booklet and a step by step photo manual. All the parts are laser pre-cut and very clean.

These boats, around 16 feet in length are usually crew by two men and are mainly used for fishing mackerel and sardine, although they can be used for any other fish or crustaceans that might be attracted by the light shining down from the large gas-lit lanterns. One of their particular characteristics are the two large stabilizers “escuas” to limit the rocking of the wave swell, and the replacement of the helm with two ropes that operate the rudder through the lantern support.

Charles

Tue Aug 21 2018, 02:16am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

The frame is made from strong 3.5mm plywood
And the laser cut made a precise fit
All the piece fit together perfectly and give a strong and perfectly straight hull

This is follow by building the floor and the pose of the deck

The hull planking start by installing 3 plank install 7mm from the edge of the deck

Charles

Tue Aug 21 2018, 02:17am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

The planking continued with plank that goes from one end to the other photo

Just to show how it is possible to mist completely and I did not try to do any correction on it.
The reason was to show when you have 2 layers of planking how it is possible to made the correction and have a nice hull at the end

More planking of the hull

Here how the hull look after the first planking I am voluntary let show the defect to show how easy it is to correct them.

Charles

Tue Aug 21 2018, 02:18am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

the hull after a first small sanding

And the the hull already look a bit better

the final sanding and photo the application of off wood filling.

Charles

Tue Aug 21 2018, 02:19am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

I glue the 2 stem in place front and back the fact that both end are round did make the planking of the hull more difficult

The sanding is almost finish and the hull start to look a lots better

Now the hull is ready to received the second planking all the defect are gone and I have now a nice hull

Charles

Tue Aug 21 2018, 02:20am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

The deck planking and the installation of the first plywood side

Those plywood do not bent easily so I use heat and a bending iron photo 6-3 to give them the proper bent

the final mounting the adjustment between the hull and the plywood side do not adjust nicely so a bit more wood putty and more sanding

Charles

Tue Aug 21 2018, 02:21am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

The second planking went like a charm and did not cause me any problem

One of the only 2 modification that I did on that build is to add some planking on the inside of the deck

I install the rudder Usually that installation cause me some problem but not this time

I finish the deck by doing some cutting and installing some plywood part I finish those step by painting the deck a light Ochre

Now the hull is completely paint and install on his base

Charles

Tue Aug 21 2018, 02:22am

Registered Member #1923

Joined: Mon Nov 28 2011, 06:07pm
Posts: 1008

Ok this will be the last post

The making of all the small part went like a breeze the oar the buoy the anchor and the pall, the basket came with the kit, the propane gas tank came preformed.

The only thing that was a but touchy was the making of the lanterns as the supports consist of a thick copper wire that came in big coil, the frame is in wood ant the 2 elbow are cast metal and very fragile.
On the lantern I made my second modification as I add light bulb. The lantern itself are perform.

Conclusion on that kit
Nice little kit not expensive and easy to build
All together around 50h of building time on each .

I do recommend it as a first wood kit

aew

Tue Aug 21 2018, 08:38am

Arthur

Registered Member #1929

Joined: Wed Nov 30 2011, 03:05pm
Posts: 3019

Interesting model.
I do remember seeing one of these before, presumably Shere's model, but that model isn't in the index, so it must have been on the DryDockModels forum.